Guide
How to call a show
The show caller is the one voice on comms that tells every department when to act. Here is how the job works in corporate and conference shows.
To call a show, you follow the run of show and give each department two spoken commands on comms. A "standby" a few seconds ahead tells operators which cue is coming. "Go" tells them to execute it now. The show caller watches the stage, the clock and the next row at the same time, and is the only person who says "go".
ON THIS PAGE
What a show caller does
A show caller (in theatre, the stage manager calling the show; in broadcast, the director) keeps the performance in time by telling every operator when to act. Lighting, audio, video, graphics and cameras each know how to do their cue. The caller decides when.
That means one person is responsible for three things at once:
- Now: is the current segment going to plan?
- Next: is everyone ready for the cue that is coming?
- The clock: are we ahead or behind, and does anything need to change?
Standby and go
Almost every cue is called in two parts.
| Call | When | What it means | What the operator does |
|---|---|---|---|
| Warning | About a minute ahead, for complex cues | A cue or sequence is coming | Finds their place, says nothing |
| Standby | 5 to 15 seconds ahead | Be ready on this cue | Hand on the button, replies "standing by" if the house style asks for it |
| Go | The moment of execution | Do it now | Executes on the word "go" |
The word "go" is reserved. The caller says it only to fire a cue, and nobody else says it on comms at all. If you need to talk about a cue, say "the G-O" or "when I call it".
A typical sequence around a speaker introduction sounds like this:
"Standby lights 12, sound 8 and graphics 21 for the keynote walk-on." "Lights 12 and sound 8, go." "Graphics 21, go." "Standby camera 1 on the lectern."
Notice the order: department, cue number, then "go" last. Operators act on the final word, so everything they need comes before it.
What to say, and what not to
- Be brief. Department, number, go. Explanations belong in rehearsal.
- Be consistent. Use the same words for the same things every time. Operators learn your rhythm.
- Keep the channel clear. Chat stops when a standby is given and resumes after the go.
- Call by number and name both, when it helps. "Graphics 21, the sponsor loop" removes doubt.
- Say what you see. "Speaker is walking" is more useful than silence when a cue depends on a person.
Conventions vary by country, venue and discipline. Theatre callers in the UK and US differ in small ways, and broadcast directors use "ready" and "take" for cameras rather than "standby" and "go". What matters is that one show uses one convention and everyone agrees it before doors.
Before the show
- Mark up the run of show. Put standbys where you will say them, usually one row ahead. Group cues that fire together.
- Find the cue triggers. Every cue fires on something: a clock time, a word in a script, a person reaching a mark, the end of a video. Write the trigger next to the cue.
- Hold a paper tech. Talk through every cue with department heads at a table. It is faster and cheaper than discovering a missing cue in the room.
- Rehearse transitions, not content. You rarely have time to run every talk. Run every handover: top and tail each segment so the changes are practiced.
- Agree the fallbacks. If a video does not play, who speaks and what goes on screen? Decide it once, in daylight.
During the show
Keep a steady loop: watch the stage, glance at the time remaining on the current item, read the next row, give the standby, call the go, repeat. Three numbers do most of the work, and they are covered in five numbers every show caller watches:
- Time remaining in the current item.
- Over or under against the plan.
- Time until the hard out.
Tell the producer early when the show drifts. "We are four minutes over, I suggest we take Q&A down to five" gives them a decision while there is still time to make it.
When the show goes off plan
It will. A speaker skips a section, a video fails, a panel will not end.
- Say what is happening, plainly. "We are skipping cue 31. Next is cue 32."
- Give a fresh standby. After any change, re-establish what is next for every affected department.
- Hold rather than guess. "Hold" means stay where you are and wait for my call. It is always safer than a cue fired on a hunch.
- Use the screens. A message on the confidence monitor ("Please wrap up", "Skip to slide 30") reaches a speaker without anyone walking on stage. See keeping speakers on time.
Calling from software
On paper, the caller tracks the current row with a ruler and a pencil. In run of show software, pressing Next advances the highlighted row for everyone, starts that item's timer on the stage display, and records the actual length. The crew can see which cue is live without asking, and the caller's attention stays on the stage. That is the job runofsho is built around: one rundown, one active cue, visible on every screen.
FAQ
What is a show caller?
The person who cues every technical department during a live event. They follow the run of show and call "standby" and "go" over the intercom so lighting, sound, video and stage crew act at the right moment.
What is the difference between a show caller and a stage manager?
In theatre, the stage manager usually calls the show as well as running rehearsals and the backstage team. In corporate events and conferences, the roles are often split: the show caller sits at front of house or in the booth and calls cues, and the stage manager works backstage with presenters.
What does standby mean?
"Standby" tells an operator that their cue is next and to be ready to execute it. It is followed by "go". Until they hear "go", they do nothing.
Why does only the show caller say go?
Operators are trained to act on the word. If anyone else says it on comms, a cue can fire early. Keeping the word for one voice removes that risk.
How do I practice calling a show?
Mark up a run of show and call it aloud against a recording of a past event or a rehearsal video. Practice the rhythm of standby and go until the wording is automatic, then practice recovering from a skipped cue.